Antique Lock Repair

Bringing a little mechanical buddy back to life.

 

This article has an accompanying four-part video series in the Patreon feed. Sign up at the Noble Patron level to see them!

A good friend of mine recently bought a house built in 1924. It has many beautiful period details, including the original mortise lock set in the front door. A mortise lock set is a one-piece mechanism that includes one or more locks and latches all in one unit. It’s called a “mortise lock” because to install it you have to cut a huge mortise (square cavity) in the end of the door. This is not the easiest thing to do, and it requires your door to made of a quality solid hardwood. The combination of installation difficulty and doors being made of other materials likely led to the downfall of these mechanisms. They are marvels of engineering, however, and were absolutely built to last. This one has been in continuous use for nearly 100 years, and though it wasn’t working well anymore, it’s surprising how little was actually wrong with it. This effort wasn’t just an idle curiosity. The broken original door hardware had prompted previous owners to install a modern deadbolt and a criminally hideous security gate over the original door. By restoring this lock set we will be doing a great service to the neighborhood.

The original is a full featured lock set, including a door latch with multiple modes, and a deadbolt. There are also automatic coordination features in the deadbolt, as we’ll see. These are the sorts of tricks you can do with a one-piece lock and latch set that modern deadbolts have forgone in the name of inexpensive installation.

 

Here’s the external facing original hardware, with modern deadbolt installed above. Because most of the major features of the original lock set are non-functional, this door hardware is acting as a handle to pull the door closed, and little else.

 

On the inside, we see the original deadbolt and handle. These parts are all hand-forged wrought iron. Nowadays everything called “wrought iron” is actually mild steel. But this is the real deal!

 

The first step is to get the lock set out of the door. Let’s see what we’re facing here.

 

As is typical for 100-year-old door hardware, it has been painted over 361 times. Some of those layers may even have lead in them, so no eating the paint, please. It’s delicious- trust me, I know. But do refrain. My cat’s breath smells like cat food.

 

It was so well sealed in there that it took a fair amount of quality time with razor blades and knives to free it from the paint. In principle, once liberated, it slides right out of the door.

Before we can do that, however, the handles must be removed. In this sense, mortise locks are very much like modern hardware- the handles are holding everything in, and are last-on-first-off.

 

The door handles are really interesting. They are captive to the trim plates, so the trim is actually holding everything together. This one has a motley crew of screws in various holes, some of which may not be factory. It’s hard to tell. It looks like there are multiple factory mounting options, and a mix were used because the wood was stripped in a couple of them.

 

Now we get our first look at the original wood of the door. It’s in very good condition, with no signs of rot or termite damage. As I said, some of the original mounting holes are chewed up, and someone even tried to repair one with a drywall anchor. People are monsters.

 

Behind the door hardware, we see the original stain and/or preservative is intact as well, which is nice. This may be creosote or linseed-oil-based. Furniture from this period would have likely used shellac, but something structural like a door would not have such a labor-intensive process in a middle-class home.

 

On the front side, the outer handle removes the same way. The little flower detail is a trap door that hides a deadbolt. The deadbolt that is in there is a modern replacement. You can still buy lock cylinders for these old lock sets. It’s also non-functional, however, and instead of fixing it, the previous owners cut a new hole in the door and installed a new deadbolt above the old. Such a shame.

 

With the handles removed, we can turn our attention to the lock set itself.

 

It’s mounted into the door with these nice original brass wood screws. We’ll save these for reinstallation. Those two holes right next to my finger hide very long setscrews that secure the deadbolt lock cylinder. Those must be removed, then the lock can be unscrewed from the front, completely freeing the lock from the door.

 

The lock did then slide out of the door, although there was a lot of resistance, for reasons we’ll see shortly. Patrons can see video of the removal in the Patreon feeds, along with lots more details on this repair.

 

With all the parts on the bench, we can now see what we’re dealing with.

 

The first step is to take the cover off. We know there are at least three problems we’re trying to solve- the door did not latch, the deadbolt handle spun freely with no effect, and the latch mode buttons on the front appeared to have no effect.

 

Right off the bat, we see the first problem. Someone has repaired this previously in creative fashion. This is a modern machine screw that has had the head filed flat. It’s nowhere close to flush, however, and this is what caused the lock to be difficult to remove from the door.

 

That creative repair was part of what held the case together and something went “sproing” inside when I removed it. That’s always unsettling, but let’s get inside and see what’s what.

 

The good news is that all the parts are here, and nothing appears to be broken. I fully expected much worse, given the range of problems the lock has.

 

Mostly, everything was really really dirty. Like, really filthy. It’s almost like nobody has taken it apart and cleaned it for 100 years. There was a nice spider nest in one corner, but even that was abandoned. She was all, “the rent was cheap, but it’s filthy! I’m outta here as soon as these 258 kids are born”.

You never know what you’ll find inside old machinery, and this was a really notable example of that. If I was up against a wall with a gun to my head, I could not tell you how a name tag from a 1970s-era embossing label maker got inside this sealed lock set.

 

WHO ARE YOU LUPE, AND HOW DID YOUR NAME GET IN HERE?

 

Anyhoo, now that we’re in like Quinn (hi Scott), we can see what’s going on and what might need fixing.

The first question is the mode buttons on the front edge. In one position, these allow you to open the door with the handle from other side, as normal. In the other position, only the inner door handle can work the latch. It’s kind of a “soft lock”. It’s roughly equivalent to the handle lock on a modern bathroom door, except that you can lock yourself out quite irrevocably with this. No key or pick will let you back in if the door swings closed behind you. It’s a neat feature though, and a nice little extra layer of security. The mode buttons seemed to have no effect on this device, however.

 

Here’s how the mode buttons work. The external door handle presses on the latch via this bottom-side button with an arm that goes through the door. That button is blocked from activating the normal latch if the lower button is pressed inward.

 

In this case, it seemed that things were just seized up. Cleaning and lubrication should sort it out. There’s nothing physically broken or out of place here.

The next problem to look at is that the normal door latch didn’t catch when the door was closed. The plunger didn’t spring back outward after being pushed in.

 

The latch was another case of things being dirty and seized up. Cleaning and lube should fix this as well. Both the dead bolt and the normal latch are very sticky and hard to move.

 

There’s a complex linkage connecting the latch and the deadbolt that is really interesting. It’s a feature whereby when you turn the key to unlock the deadbolt, if you turn a little further, it also pulls the main latch backwards. This allows you to unlock and open the door in one motion. The deadbolt also has a linkage that disables the door latch when extended, so it’s actually a double-lock of sorts. These locks are really clever, and delightfully well-engineered.

The final question was the deadbolt, wherein the handle spun freely with no effect. This was definitely going to be something broken.

 

Here’s our culprit. The shaft on the handle snapped off. This is hand forged wrought iron, and it gets pretty thin here, so this isn’t too shocking. Likely someone forced it when the dead bolt got stuck.

 

Okay, so this all seems fixable. Let’s get this thing taken apart and cleaned up.

 

Here’s a closeup look at a part that is typical of what’s in this lock. It’s cast brass (or possibly bronze) and very intricate. This is a very elaborate mechanism with a lot of moving parts, but it’s incredibly robust. I mean, it has lasted 100 years, and probably has another 100 in it with a little TLC.

 

 

Here’s the whole lock, disassembled and thoroughly cleaned. It looks like new! Half the engineering in this lock is in the casting of the enclosure. Every little recess and boss in there serves a purpose. These static features form catches, bearing surfaces, support fixtures, retainers, and other things. A lot of design has gone into this, and casting something this complex would take substantial foundry experience.

 

Here’s a close-up of the mode-button subassembly, which is very clever. The pair act like radio buttons, and the lower one has the little bump that blocks the linkage on the external door latch as needed.

 

This fairly-modern deadbolt cylinder was installed in the unit, but my friend was not given the key to it. She’s going to have it re-keyed, or replace it. You can still buy these, as this “modular” deadbolt cylinder standard has been kept up.

 

Cleaning and lubrication should solve most of the issues, but not all. We have three parts that need more invasive attention. First is that broken deadbolt handle. I decided to make an extension for the rod and braze it on. You can weld wrought iron (it welds very well, in fact), but it’s a small part and I don’t trust my skills to do that. Brazing should be plenty strong, however.

 

You can see that the original deadbolt shaft was quite a bit thinner than it needed to be. There’s plenty of room here for a bigger (and thus stronger shaft).

 

Okay, let’s repair and extend that shaft. To the machine shop!

 

I milled a square shaft extension on the vertical mill, then milled out a little pocket to accept the original shaft.

 

Here’s how the extension will work. I left it extra long, because I didn’t have access to the door, so I wasn’t sure how long it needed to be. I would simply cut it to length on site during reinstallation.

 

This brazed up very well, and should be as strong as it ever was from the factory. Good for another hundred years!

 

The next thing to address is the bolt that a previous repairperson had made to (presumably) replace a factory pin. In addition to being one of the screws holding the case together, it was also anchoring one of the springs that forms the latch mechanism. As I said before, the repair was a clunky ground-down machine screw that stuck out way too far and interfered with installation of the lock. I grabbed some brass off the junk pile and made a replacement. Patreon Patrons can see video of the making of this screw, so sign up now if you’d like to be one of them. They had drilled out the boss on the enclosure that holds this bolt, and I can’t change that, so I made the new bolt to the same dimensions, but in the style of the original hardware.

 

Here’s the replacement screw I made, which is a much better fit, both physically and (I think) aesthetically. The process of making it was very cool and you should sign up to see it.

 

My replacement sits flush on the lock’s case, as it needs to do for proper lock installation.

 

The final thing to address is the latching door handle. While cleaning and lubrication fixed the internal mechanism, the handle itself was sloppy and didn’t feel right. A quick inspection of the parts revealed why. The handle has a shaft that threads into it, and the handle clamps to said shaft with a pair of setscrews. The other end is square, and slides into the latch mechanism. However, this shaft was so worn out that it was hard to tell what shape it was even supposed to be. The setscrews were barely holding the handle in place, and the fit was very sloppy. The threads on the inside of the handle were also quite trashed.

 

The threads inside the handle have been rubbed flat by many decades of use and abuse. There’s plenty of meat here though, so recutting them a larger size with the same pitch should be successful.

 

Since I was going to have to make a new shaft anyway, I decided to cut new threads in the handle. I opted to match the pitch of the old ones (there was enough left there to measure), but choose a larger diameter. The tap should find the old threads and simply enlarge them. The old threads were 18-per-inch (measured with a thread gauge), which is still a common standard. Conveniently, the dimensions of the worn hole were the tapping size for a ⅜” thread, so I opened up the threads to ⅜-18. Doing this straight was a tricky job, because the entire handle is a hand-wrought pile of curves. There’s nary a straight line or flat surface on the entire structure anywhere.

 

I aligned the hole by installing the factory shaft and snugging it down. The hole in the bottom was still okay, so the shaft straightened up when tightened far enough. This shaft could then be used with an indicator to find “vertical”.

 

I then used a tap follower in the mill to hold the tap straight and centered, and retapped the hole to my larger size.

 

Next I needed to remake the shaft. Since the original was so trashed, I couldn’t really tell what it was supposed to look like. However the way it worked was easy enough to deduce, so I made a new part that did the same job and mated to the other parts I had. Things are a bit worn inside the lock, so mine would be a better fit anyway.

I have video of the making of this shaft as well. To see it, head on over to the Patreon Patrons feed, or sign up now to get access.

 

I made this new shaft with the lathe and the vertical mill. It was a very interesting part to make, especially since the original was so trashed it was hard to tell what it’s supposed to look like. Sign up on Patreon to see video of the making of this part!

 

You’ll note the grooves on the shaft. These are for the setscrews on the handle. The original had four grooves, but I made only two. Four grooves, in my opinion, only serve to weaken the threads on the shaft. In theory four grooves provide four different orientations for the handle, but you can get that same effect by adjusting how the shaft inserts into the lock mechanism. Either way you get four possible handle positions, so two grooves are sufficient. I suspect the original was made this way for cheaper manufacturing. It’s clearly cut from bar stock that has the groove already in it on all four sides, rather than being bespoke-machined from scratch as my replacement is.

The final step was to clean every part thoroughly, then lubricate and reassemble the whole lock. I took photos during disassembly so I could remember how it all went, but truth be told you could probably figure it out. There’s only one way it all goes back together, it just saves time not to have to reverse engineer it from scratch at reassembly time.

For lubrication, not being a locksmith, I did some research on the tuberwebs. The general recommendation seems to be dry graphite lubricant for a lock like this, because it won’t evaporate (like many liquid lubricants would), won’t drip off the parts (like oil would), and won’t get gummed up with crud over time (like grease would). The other nice thing about dry graphite lube is that you can get it in an aerosol, suspended in alcohol. As needed, you can inject it into the lock through any available crack after the lock is reinstalled. The alcohol flashes off and you’re left with a dry layer of graphite on things. I gave everything a good coating during assembly which should last a good long while. The sad part of this approach is it makes everything black, after I just spent time making it all look nice inside.

For a look at lubrication and reassembly, check out the associated Patreon video for this post. Yes, that’s four videos to go along with this blog post. That’s how much I heart you, Patrons.

 

We’re about ready to reinstall things back at the house. First step is to cut the deadbolt extension shaft to length.

 

With the repaired deadbolt shaft cut and filed to length, we’re ready to reassemble everything.

 

Assembly is the reverse of removal. The lock set is slid into the mortise and secured with the large screws at top and bottom. Then the deadbolt cylinder is threaded into the front. There are two very long set screws that go into the end plate of the device to secure the lock cylinder and prevent it from being unscrewed from the outside. Then the door handles and deadbolt handle can be reinstalled on the two sides of the door.

 

With the lock back in place, the repaired deadbolt handle can go back on.

 

With everything back together, I’m pleased to say every feature on the door now works perfectly, and should be good for another hundred years. This was a mechanical restoration, not a cosmetic one, so there’s a little more work to do around removing sloppy old paint from the wrought iron, replacing some of the screws, and so on. For a look at the final result and a demo of all the features of this old lock, you’ll want to check out the Patreon videos.

After completing the project, I received this update from the happy customer: “Door hardware functioning within normal parameters.”. That’s the highest compliment an engineer can receive.

 

As the final pièce de résistance, the homeowner was able to remove a horrible security gate that is no longer needed now that the original door hardware is functional again. That beautiful 100yo solid hardwood door can show itself once again!

11 thoughts on “Antique Lock Repair

  1. Excellent restoration, and a great write up.
    I enjoyed reading that.

    I installed four reclaimed age appropriate 1870s pitch pine internal doors in my house, replacing the modern fire doors that were there. Each door had an original lockset but no keys. I was able to remove, open, clean, and make new keys to fit each door. The doors are never locked, though, but nice to know they can be.

    1. That’s great! I love stuff like this- it was built to last, and to be repaired, often with basic tools (because frankly, they were made with basic tools).

  2. “We’re in like Quinn” – I would adopt this phrase if I thought I knew anyone else who would appreciate it. It would make a nice T-shirt design along with that picture of all the knolled dismantled lock parts

  3. “That creative repair was part of what held the case together and something went “sproing” inside when I removed it. That’s always unsettling, but let’s get inside and see what’s what.”

    That made me laugh out loud, because that exact same thing happened to me when I opened up a mortise lock to fix it.

  4. “That creative repair was part of what held the case together and something went “sproing” inside when I removed it. That’s always unsettling, but let’s get inside and see what’s what.”

    That made me laugh out loud, because that exact same thing happened to me when I opened up a mortise lock to fix it.

  5. I grew up in a house with these all over the place. Even the interior doors had them, but with locking mechanisms which took skeleton keys. The major problem we had was all of the encrusted layers of paint which got slapped on haphazardly. Excellent work!

Comments are closed.

Mini Cart 0

Your cart is empty.